Boat Anodes: Zinc, Aluminium or Magnesium? A Practical Guide

Boat Anodes: Zinc, Aluminium or Magnesium? A Practical Guide

November 17, 2026•By MPS

By MarinePartSystem, 17 November 2026.

Quick answer

Use magnesium only in fresh water. In salt and brackish water Volvo Penta now recommends aluminium, and zinc still works in salt water. Check your anodes every time the boat comes out of the water and replace them when about half is gone. Order anodes for your exact drive (saildrive, sterndrive or shaft), and keep one metal across the whole boat.

What an anode actually does

Every metal part under the waterline sits in an electrolyte: the water. When two different metals are connected in that water, the less noble one corrodes first. An anode is a piece of metal that is less noble than your drive, propeller and shaft, so it corrodes instead of them. That is why it is called a sacrificial anode.

An anode that wears away is doing its job. An anode that looks brand new after a full season is often the real worry, because it may not be protecting anything.

Which anode metal for which water?

This is the question we get most. The answer depends on where the boat spends most of its time.

Water Best choice Notes
Salt water Aluminium or zinc Volvo Penta now recommends aluminium here (it used to recommend zinc)
Brackish water Aluminium Zinc is less effective at lower salt levels
Fresh water (rivers, lakes, canals) Magnesium Never use magnesium in salt or brackish water
Moving between fresh and salt Aluminium Swap magnesium for aluminium before you go to sea

A few things worth knowing:

  • Volvo Penta’s own catalogue says it now recommends aluminium anodes in salt and brackish water, instead of zinc as it recommended before.
  • Magnesium in salt water wears very fast and produces hydrogen, which can damage paint and coatings. Anode manufacturers are very clear on this: magnesium is for fresh water only.
  • Zinc in fresh water can build up an oxide layer that stops it working.

In the Netherlands many boats sit in fresh or brackish water most of the year, so check what your boat came with before you simply reorder the same metal.

Where the anodes are on your boat

Most boats have more than one anode, and each one protects the part it is fitted to.

  • Saildrive: a ring anode around the propeller hub, or split ring halves on some drives. Volvo Penta 110S, 120S, 130S, 150S and MS25S, and Yanmar SD20 to SD60, all take their own type.
  • Sterndrive: a set of anodes on the drive, the cavitation plate and the transom shield. Volvo Penta SX, DP and 280/290 drives and MerCruiser Alpha One and Bravo drives each have their own kit.
  • Shaft drive: a shaft anode (collar) on the propeller shaft, sometimes a propeller nut anode.
  • Hull, rudder and bow thruster: separate anodes, especially on steel and aluminium hulls.
  • Engine: many marine diesels also have a small anode in the cooling system.

The drive anode is designed to protect the drive. Extra metal below the waterline, such as a bow thruster or a metal hull, needs its own protection.

When to replace an anode

The Volvo Penta D1/D2 manual says to check the drive anodes every time the boat is out of the water and to replace them when 50% is consumed. Some Volvo Penta sterndrive manuals are stricter and say replace once a third has worn away. When in doubt, follow the manual for your drive.

In practice:

  • Check every haul-out, and at least once a season.
  • Replace at about half worn. Do not wait for the bolts to show. A small anode cannot protect a big drive for long.
  • Replace if it is painted. Paint on an anode stops it working. Never paint anodes.
  • Clean before launch. Volvo Penta says to clean and polish anodes with emery cloth before launching, because oxidation builds up while the boat is ashore. Do not use a wire brush or abrasives with metal in them.

Warning signs

What you see What it can mean What to do
Anode hardly worn after a season Poor contact, paint on the anode, or the wrong metal for your water Check the contact surfaces and the metal type
Anode gone within weeks Stray current, shore power issue, or magnesium in salt water Check the metal type and have the electrics tested
White crust on the anode Oxide layer, often zinc in fresh water Clean it, or switch to the right metal
Pitting on the drive or propeller Anodes worn out or not working Replace the anodes now and have the drive checked

Fitting a new anode

  1. Clean the mounting surface until it is bare metal. No paint, grease or corrosion.
  2. Clean the contact surface of the new anode as well.
  3. Fit it with the hardware from the kit and tighten so it makes good contact with the drive or shaft.
  4. Use one anode metal across the whole boat. Mixing metals makes them wear unevenly.
  5. Write down the date and the engine hours, so you know how fast your anodes wear.

On a saildrive or a sterndrive, a complete kit is usually easier than buying single pieces, because it includes all anodes and the bolts for that drive.

Anodes by drive type

Volvo Penta saildrives

The 120S takes ring anode 851983 / 876286, and we stock it in zinc, aluminium and magnesium. For the 130S, 150S and MS25S our zinc anode replaces 3888305 and 22651246, and the magnesium version replaces 3888306.

Yanmar saildrives

The Yanmar SD20, SD25, SD30, SD31, SD40, SD50 and SD60 take the same anode kit, which we stock in zinc, aluminium and magnesium with the mounting hardware.

Volvo Penta sterndrives

We stock complete anode kits with hardware for the SX / DP-SM, DPH / DPR, 280 and 290 Duo Prop drives in aluminium, zinc or magnesium, depending on the drive.

MerCruiser sterndrives

New in the shop: aftermarket anode kits and single anodes for MerCruiser Alpha One Gen 1 and Gen 2, Bravo I, Bravo II and Bravo III, in zinc, aluminium and magnesium. For example, the Alpha One Gen 2 zinc kit replaces 888755Q03 and the Alpha One cavitation plate anode replaces 821629. These are aftermarket parts, not genuine Mercury parts.

Parts for this job

The cards below link straight to the product pages, where you always see the current price and stock.

Volvo Penta 120S Saildrive Aluminium Anode | 851983-876286

Volvo Penta 120S Saildrive Aluminium Anode | 851983-876286

Fits: Volvo Penta 120S saildrive
Part no.: 851983 / 876286

View product
Anode Zinc Volvo Penta 130/150 (22651246, 3883728, 3888305)

Anode Zinc Volvo Penta 130/150 (22651246, 3883728, 3888305)

Fits: Volvo Penta 120S, 130S, 150S, MS25S
Part no.: Replaces 3888305, 22651246

View product
Volvo Penta Magnesium Anode 120S, 130S, 150S & MS25S -3888306

Volvo Penta Magnesium Anode 120S, 130S, 150S & MS25S -3888306

Fits: Volvo Penta 120S, 130S, 150S, MS25S
Part no.: Replaces 3888306

View product
Volvo Penta Anode Kit SX / DP-SM – Aluminium | Complete with Hardware

Volvo Penta Anode Kit SX / DP-SM – Aluminium | Complete with Hardware

Fits: Volvo Penta SX, DP-SM
Part no.: Kit with hardware

View product
Volvo Penta Anode Kit DPH/DPR – Aluminium | Complete with Hardware

Volvo Penta Anode Kit DPH/DPR – Aluminium | Complete with Hardware

Fits: Volvo Penta DPH, DPR
Part no.: Kit with hardware

View product
Aluminium Anode Kit Alpha One Gen 2 for MerCruiser

Aluminium Anode Kit Alpha One Gen 2 for MerCruiser

Fits: MerCruiser Alpha One Gen 2
Part no.: Kit with hardware

View product
Aluminium Anode Kit Bravo I for MerCruiser

Aluminium Anode Kit Bravo I for MerCruiser

Fits: MerCruiser Bravo I
Part no.: Kit with hardware

View product
Aluminium Anode for Volvo Penta - 838929

Aluminium Anode for Volvo Penta – 838929

Brand: Volvo Penta
Part no.: Replaces 838929

View product
Zinc Anode for Yanmar - 27210-200300

Zinc Anode for Yanmar – 27210-200300

Brand: Yanmar
Part no.: Replaces 27210-200300

View product

Which anode fits my drive?

Send us your drive type and serial number, or a photo of the old anode next to a tape measure. We check the part number before you order, so you get the right anode the first time.

Ask us which anode fits+31 6 8243 9981info@marinepartsystem.com

Frequently asked questions

Zinc or aluminium anode: which is better?

In salt and brackish water Volvo Penta now recommends aluminium. Zinc still works in salt water. In fresh water neither is the best choice: use magnesium.

Can I use magnesium anodes in salt water?

No. Magnesium wears very fast in salt water and the hydrogen it gives off can damage paint and coatings. Use it in fresh water only.

How often should I replace my boat anodes?

Check them every time the boat is out of the water and replace them when about half has worn away.

Can I mix zinc and aluminium anodes?

It is better not to. Use one metal across the boat so the anodes wear evenly.

Are aftermarket anodes as good as genuine ones?

A good aftermarket anode in the right alloy protects just as well. If your drive is still under warranty, check what your warranty terms ask for.

Shop anodes by type

All boat anodesSaildrive anodesSterndrive and pod drive anodesShaft anodesHull anodesVolvo Penta anodesYanmar anodes

Read next

Sources

  • Volvo Penta Accessories and Maintenance Parts catalogue: aluminium recommended in salt and brackish water instead of zinc.
  • Volvo Penta D1/D2 service and maintenance manual: check anodes at every haul-out, replace at 50%, clean with emery cloth before launching, no wire brush, magnesium for fresh water.
  • Volvo Penta sterndrive operator's manual (47700385): do not paint anodes, replace at 2/3 of original size on that drive.
  • Anode manufacturer guidance: magnesium only in fresh water.
  • MarinePartSystem product data (WooCommerce, read 17 Nov 2026): part numbers and fitment.
Share:
Boat Anodes: Zinc, Aluminium or Magnesium? When to Replace | MPS